- 三元催化还原修复剂
-
采用浓缩型的超分子技术,能很好地去除三元催化器上的硫、铅、磷、锌等化学物质。
三元催化还原修复剂由美国ubrizol-AKO、美国陶氏公司提供原料原料及技术支持,扎根中国汽车养护用品研发一级学府--华南理工大学化工系,精心研发而成!
三元催化还原修复剂
保养时间:20000-30000公里
爱蔻三元催化还原修复剂
产品编号:AKO-118/480ML
企业标准:Q/YK 012-2009
产品仅供4S店使用
产品性能
1、高效分解三元催化、氧传感器上的硫、铅、磷、锌等化学物质。
2、重新激活三元催化器中铂、铑、钯的净化功能,大幅降低汽车尾气中CO、HC、NOX的排放。
3、提升燃油燃烧效率,提高冷车启动性能,恢复汽车原有动力,降低油耗。
4、延长三元催化器及氧传器的使用寿命,减少维护综合成本。
使用方法
1:起动汽车发动机至正常工作温度。
2:用专用油门固定器,将引擎转速固定在2500转。
3:寻找、拆开节气门后的真空管(有真空吸力)。靠近节气门第一个管口最佳。
4:把产品瓶口打开连接在专用的清洗设备上,并把设备出液透明软管与汽车的真空管对接。
5:打开设备开关,将流量调整开关调到20-30分钟的清洗时间最佳,检视产品形成泡沫进入真空管为正确除碳工作状态。
6:除碳时进气岐管由热转冰凉是最佳有效状态,除碳完成后15分钟,拔出连接产品瓶口端的管口。
7:待进气岐管由冰凉转热(用手摸进气岐管最底部确认),引擎恢复正常工作温度后进行排碳动作。
8:将油门固定器拆下,以每500转/10秒轻缓加油,逐次加至3000转;以稍快速度重复上述动作;待进排气声顺畅时,再拆开除碳元素接管,恢复原车接管,除碳中及排碳时绝不可以重踩油门。排碳后路试。
以下几种情况不能清洗:
1.三元催化器烧结或铅中毒;
2.三元催化器严重堵塞;
3.化油器车改装为三元;
4.发动机烧机油。
清洗完毕后车辆需要行驶5公里左右以便废物排出。
注意事项
1.禁止将本品直接加入油箱与汽油混合使用;
2.勿将本品溅入眼内,如不慎溅入眼中立即用清水冲洗,再去医院治疗;
3.存放阴凉干燥处,避免儿童接触。
Air System Maintenance Agent
Features:
1st, decomposes three Yuan catalyzed, oxygen chemical substances highly effective and so in sensor's sulfur, lead, phosphorus, zinc.
2nd, activates in three Yuan catalysts the platinum, the rhodium, the arrowhead purification function, restores three Yuan catalyst original performance. Reduces in largely the automobile exhaust CO, HC, the NOX emissions.
3rd, the promotion oil inflame efficiency, enhances the refrigerated car starting ability, restores the automobile original power, reduces the oil consumption.
4th, lengthens three Yuan catalysts and the oxygen pass on service life, reduces the maintenance comprehensive cost.
Use Method
1: Starting motor car engine to normal work temperature.
2: With the special-purpose accelerator anchor, fixes the speed by engine revs in 2500 revolutions.
3: After seeking for, disassembles the damper the vacuum tube (to have vacuum suction). Approaches a solar terms family status orifice to be best.
4: Opens the connection the product bottle mouth on the special-purpose decontaminatin unit, and leaves the equipment the fluid transparent hose and automobile's vacuum tube docking.
5: Turns on the equipment switch, adjusts the current capacity adjustment switch to 20-30 minute scavenging periods is best, inspected that the product forms the froth to enter the vacuum tube for the correct decarbonizing active status.
6: Decarbonizes when the intake manifold by the hot extension icy cold is the best effective condition, after decarbonizing completes, 15 minutes, draws out the connection product bottle mouth end the orifice.
7: Waits the intake manifold hot (to trace intake manifold most base confirmation by the icy cold extension with hand), after engine rehabilitation temperature, carries on the row of carbon movement.
8: Dismantles the accelerator anchor, refuels leisurely by every 500 revolution of /10 seconds, adds gradually to 3000 revolutions; Is redundant above movement by the slightly quick speed; Treats when the exhaust sound is smooth, again disassembles decarbonizes the element control, recovers extensively the vehicle control, decarbonizes and when a row of carbon may not step on the accelerator again. After arranging the carbon, driving test.
The following several kind of situations cannot clean:
1.3 Yuan catalyst agglutinations or lead poisoning;
2.3 Yuan catalysts stop up seriously;
3. the carburetor vehicle re-equipping is three Yuan;
4. the engine burns the machine oil.After the clean finished, the vehicles needed to go about 5 kilometers, so that the waste could discharge.
Note:
1、forbid to join directly in the fuel tank and the gasoline mix use;
2、This is the combustible materials, when the use should be far away from the high temperature area and the open fire, depositing cool dry place;
3、This swallows harmfully, is sure not the entrance, is far away from the child.