高新技术企业 · 汽车深度养护品专业供应商

全国招商热线:13318861726

当前位置:首页 > 产品中心 > UD 优道 > 进排气系统进排气系统
缸内直喷清洗剂

缸内直喷清洗剂采用强力溶解分散气门口积碳技术,在发动机怠速状态下通过专用的施工设备,将清洗剂处理成细微颗粒,在进气歧管内成为雾状,与进气管、进气门油泥积碳充分附着,在一定的温度条件下,迅速溶解分散积碳,进入燃烧室燃烧后随排气排出。

  • 缸内直喷清洗剂
  • 缸内直喷清洗剂
  • 缸内直喷清洗剂

品牌:UD优道

系统:进排气系统

产品编号:UD-02.271/325ml

企业标准:Q/YKJH 8

产品仅供4S店使用


产品特点:

1、本品采用美国专利技术,专业用于直喷发动机。

2、进行免拆清洗进气歧管道、进气阀门积碳,燃烧室 积碳,排气门、排气端涡轮叶片积碳。

3、改善发动机冷启动困难,怠速不稳,加速无力油耗增大等现象。

4、提升进气效率,燃油利用率,恢复发动机动力。


使用方法:

1、进气门积碳清洗剂配合专用设备使用,汽车怠速情况下从进气歧管吸入,施工时间控制在40分钟。

2、油箱处理剂和发动机性能恢复剂直接加注油箱使用(每瓶兑40-60升汽油使用)。


项目优势:

1、免拆施工:省时、省力,施工时间约40分钟,只需配备压缩空气;

2、高性能产品组合,快速清除积碳,效果立即看得见;

3、环保配方,对橡胶、塑料、铝铁、氧传感器、三元催化器等无损坏。


项目解决问题:

1、清除进气门、进气道积碳油污;

2、清除喷油嘴、燃烧室积碳;

3、去除油箱、油路去胶质、水分;

4、对解决发动机排放灯亮有明显帮助;

5、恢复发动机新车性能、降低油耗、恢复动力、降低排放、降低噪音。



注意事项:

1、清洗过程中严格控制流量,确保施工过程在40分钟左右。若施工过程中发现怠速抖动严重,立即关小控制阀流量直到正常为止。

2、清洗剂清洁完毕之后,保持发动机怠速行驶3-5分钟,后加减油门排干净残余积碳。

3、在通风处施工。

4、对于进气门积碳比较严重的建议:拆下歧管、手工清除。


Product features:

1. This product adopts American patented technology and is specialized in direct eruption motors.

2. Conduct no-disassembly and cleaning of inlet manifold and inlet valve carbon deposition, combustion chamber carbon deposition, exhaust valve and exhaust end turbine blade carbon deposition.

3. It is difficult to improve the cold start of the engine, unstable idle speed, weak acceleration and increased fuel consumption.

4. Improve the intake efficiency, fuel efficiency and engine power recovery.


Usage:

1. The carbon cleaning agent of the intake valve is used in conjunction with the special equipment. It is inhaled from the intake manifold in idling condition and the construction time is limited to 40 minutes.

2. Fuel tank treatment agent and engine performance recovery agent are directly injected into the fuel tank for use (each bottle is used with 40-60 liters of gasoline).


Project advantages:

1. No-demolition construction: save time and effort, and the construction time is about 40 minutes. Only compressed air is required.

2. High performance product combination to quickly remove carbon accumulation, and the effect can be seen immediately;

3. Environmentally friendly formula, no damage to rubber, plastic, aluminum iron, oxygen sensor, three-element catalytic converter, etc.


Project solution:

1. Remove carbon and oil pollution from inlet valve and inlet channel;

2. Remove carbon deposits in fuel injection nozzle and combustion chamber;

3. Degumming and water removal of fuel tank and oil road;

4. It is obviously helpful to solve the problem of engine discharge lamp on.

5. Restore new engine performance, reduce fuel consumption, restore power, reduce emissions and reduce noise.


Notes:

1. Strictly control the flow of water during cleaning to ensure the construction process is around 40 minutes. If idling jitter is found to be serious during construction, turn down control valve flow until normal.

2. After cleaning the cleaning agent, keep the engine idle for 3-5 minutes, and then add and subtract the gas pedal to clean the residual carbon deposits.

3. Construction in the ventilation area.

4. Suggestions for serious carbon accumulation in the intake valve: remove the manifold and remove by hand.





返回顶部