高新技术企业 · 汽车深度养护品专业供应商

全国招商热线:13318861726

当前位置:首页 > 产品中心 > UD 优道 > 进排气系统进排气系统
三元催化高效清洗剂

1. 有效清除三元催化器表面的积碳及残留物。

2. 恢复三元催化器的净化功能,降低尾气排放。

3. 提升燃油燃烧效率,提高冷车启动性能,降低油耗,恢复发动机动力。

4. 延长三元催化器的使用寿命,减少维护综合成本。

  • 三元催化高效清洗剂
  • 三元催化高效清洗剂

优道三元催化高效清洗剂

品牌:UD优道

系统:进排气系统

产品编号:UD-01.265/325ml

企业标准:Q/YKJH 8

产品仅供4S店使用


产品特点:

1. 有效清除三元催化器表面的积碳及残留物。

2. 恢复三元催化器的净化功能,降低尾气排放。

3. 提升燃油燃烧效率,提高冷车启动性能,降低油耗,恢复发动机动力。

4. 延长三元催化器的使用寿命,减少维护综合成本。


使用方法:

1、启动发动机至正常工作温度,

2、用专用油门固定器将引擎转速固定在2500转

3、寻找、拆开节气门后的真空管(有真空吸力),靠近节气门第一个管口最佳,

4、把产品瓶口打开连接在专用清洗设备上(或倒入设备铁罐中),并把设备出液透明软管与汽车的真空管对接,

5、打开设备开关,将流量调整开关调到产品成滴入装状进入真空管为正确,清洗时间为25-30分钟最佳,

6、整瓶产品用完,除碳时间完成,拔出连接汽车真空管接头并恢复原状,

7、将油门固定器拆下,以每500转/10秒轻缓加油,逐渐加至3000转,以稍快速度重复上述动作。

8、待进排气声顺畅时再排碳15分钟,除碳中及排碳时绝不可以重踩油门,排碳后必须进行路试。


Product features:

1. Effectively remove the carbon deposition and residue on the surface of the ternary catalytic converter.

2. Restore the purification function of the three-way catalytic converter and reduce the exhaust emission.

3. Improve fuel combustion efficiency, improve start-up performance of cold vehicle, reduce fuel consumption and restore engine power.

4. Extend the service life of three-element catalytic converters and reduce the comprehensive maintenance cost.


Usage:

1. Start the engine to the normal operating temperature,

2. Fixed the engine speed at 2500 revolutions with special accelerator fixator

3. Look for and open the vacuum tube behind the throttle (with vacuum suction). It is best to be close to the first pipe opening of the throttle.

4. Open the product bottle mouth and connect it to the special cleaning equipment (or put it into the equipment tin), and connect the device's liquid outlet transparent hose to the vacuum tube of the car.

5. Turn on the device switch, and adjust the flow rate adjustment switch to the product to drip into the vacuum tube. The cleaning time is 25-30 minutes.

6. When the whole bottle of product is used up, the decarbonization time is completed, and the vacuum tube connector of the car is pulled out and restored to its original state.

7. Remove the accelerator fixator and gently refuel every 500rpm / 10s, gradually add to 3000 RPM and repeat the above action at a slightly faster speed.

8. When the inlet and exhaust sound is smooth, the carbon shall be discharged for another 15 minutes. In addition, the gas pedal shall not be pressed again when the carbon is removed and the road test shall be conducted after the carbon is discharged.




返回顶部